كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

Preparation

After receiving our products, please check if all accessories are complete as below.

1. Every flood light fixture contains an antenna.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

2. Controller kit (it contains an SD card, an AC-DC adapter, a USB cable and a remote control).

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

3. Wireless transmitter (it contains an antenna, an AD-DC adapter and a DMX cable).

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

Sometimes we will pack all accessories into the same carton. Please confirm with us.

مخطط التثبيت

The whole system mainly includes three parts: وحدة تحكم دمكس(with remote control), wireless transmitter and light fixtures.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

The DMX controller and the wireless transmitter should be connected together by a DMX cable. The transmitter will convert the wired DMX signals to wireless DMX signals and spread it to all light fixtures. After receiving the wireless signals, each light fixture will decode it and show the corresponding color and effect.

Installation Steps

1. Install the light fixture.

Our light fixtures can be installed on the floor, ceiling, wall or light pole.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

The wires info of the power supply: Red is Live wire, Blue is Neutral wire, Yellow is Ground wire.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

2. Install the antennas

There is a holder for installing antenna on the bottom of the light fixture. Please screw the antenna into the holder well by clockwise direction as the following picture. The antenna is foldable.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

You can refer to this video: https://youtu.be/BIfrylYk3cg.
The light fixture will show the default color or last color when it is given power.

3. Install the controller

The controller contains an SD card which stores the default programs, an adapter and a remote control. Insert the SD card into the controller and connect all cables well.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

4. Install the wireless transmitter

The wireless transmitter contains an antenna, an adapter and a DMX cable which is used to connect the controller. Install the antenna well and connect the transmitter and the controller together by the DMX cable.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

Please note there are four dip switches on the back side of the transmitter. Set 1, 2, 3 down and 4 up as the following picture. Usually the manufacturer has made this default setting.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

When you power up the controller and the transmitter, do not forget to push the power button on the back side of the transmitter. Its LEDs will blink after working.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

How to choose the programs?

After the controller and transmitter start to work, you can use the remote control to choose the programs. For example, press key 1 and press key PRG then the 1st program will be chosen. Before you use the remote control, please make sure it contains a battery inside. We normally take off it before the shipment. You can buy it in your local stores.

كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟
كيفية إعداد نظام ضوء الفيضانات LED اللاسلكي DMX؟

Following is our default programs with their serial numbers:

0. red
1. green
2. blue
3. white
4. yellow
5. orange
6. cyan
7. purple
8. red fading
9. green fading
10. blue fading
11. white fading
12. red/green/blue changing
13. 7 colors changing
14. shutdown

If you still have any questions on using our wireless DMX flood light system, please feel free to contact us.

اترك تعليقا

لن يتم نشر عنوان بريدك الإلكتروني. الحقول الإلزامية مشار إليها بـ *

arالعربية
Scroll to Top